This pendant is demonstrated using square copper wire for the frame, half round nickel silver for the links, and round bronze wire for the jump ring and bail wires. You may use any wire of your choice to either match or contrast the components, and half-hard temper seems to be more secure. Have fun! -Denny
Materials
H7-14HRD 14-gauge dead soft half round Nickle Silver
Lesson Quantity: 38.00 inches
Purchase Quantity: 1.00 each
14 Gauge Square Dead Soft Copper Wire
H11-14SQD
Lesson Quantity: 8.75 inches
Purchase Quantity: 1.00 1FT
Price: $3.45
Gold Club Price: $2.59
Add to Bag
16 Gauge Round Dead Soft Yellow Brass Wire
H1-16D
Lesson Quantity: 4.75 inches
Purchase Quantity: 1.00 1FT
Price: $0.98
Gold Club Price: $0.73
Add to Bag
Add All Items to Cart
Tools
Flat Nose Wire Plier
G2-506
G2-506
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $32.95
Gold Club Price: $24.71
Add to Bag
Round Nose Wire Plier
G2-507
G2-507
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $32.95
Gold Club Price: $24.71
Add to Bag
3 Step Wire Wrapping Flat Nose Pliers - Pack of 1
G2-85
G2-85
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $9.97
Gold Club Price: $7.48
Add to Bag
C.H.P Milano Italian Flush Cutter, 5 1/2 Inches
PLR-487.00
PLR-487.00
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $14.97
Gold Club Price: $11.23
Add to Bag
3.6 Volt Automatic Wire Twister (Cordless Screwdriver)
G5-15
G5-15
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $42.97
Gold Club Price: $32.23
Add to Bag
8 Piece Mandrel Set - From 1/16 Inch to 5/16 Inch
G7-38
G7-38
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Price: $7.97
Gold Club Price: $5.98
Add to Bag
Marker -extra fine
Lesson Quantity: 1.00 pieces
Purchase Quantity: 1.00 each
Add All Items to Cart
Instructions
Step 1
Straighten and cut 18 pieces of 14-gauge half round wire, each 2-3/8" (6cm) long. Mark the centers of those wires at 3cm.
Step 2
Hold wire with flat nose pliers, then gently bend the wire, bending a loop on the edge of the half round wire. The rounded side should be up, and the flat side should be down.
Step 3
Use your pencil or dowel to keep the rounded loop, then pinch the wire ends together to close.
Step 4
Bend 2 loops gently: 1 piece with rounded side up, 1 with flat side up. Intertwine the pieces, aligning them with both rounded sides facing upward.
Step 5
Flatten one of the loops' ends. Using the smallest step of 3-step pliers, curl the ends coming out over the rounded (top) side of the link, until that end touches the flat side. Repeat on the other side, this time with the flat (bottom) side curling upward. This is your first knot.
Step 6
Make 1 jump ring from 16-gauge round wire, using a Sharpie marker as a mandrel.
Step 7
Make 8 more knots. Slide all knots onto the jump ring with the rounded (top) side of the curl outward.
Step 8
Twist the 14-gauge square wire into a nice bead, or diamond-cut, pattern. Wrap the twisted wire around a bottle or dowel approx. 2-1/8" in diameter, and mark where the wires meet.
Step 9
Measure 3/4" from the mark towards each end of the wire, and then cut off the excess.
Step 10
Using the middle step of 3-step pliers, make a loop so that one end meets the mark. Leave the other end straight.
Step 11
Thread the twisted wire through the flat side-showing end of the 9 knots. Finish top of frame with a loop matching the loop in step 10.
Step 12
Move knots evenly around circle and crimp firmly onto frame with flat nose pliers.
Step 13
Use 16-gauge round wire to make 2 s-shaped closed hooks to secure the frame loops as bails, or make a bail of your choice.
Supply Detail
loading...
Change Metal:
This Pattern requires:
Purchase quantity:
Price: $
Gold Club Price: $